AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Easy cat pictures4/29/2023 ![]() Cover a tall board or long pole with sisal rope by attaching the end of the rope to the bottom of the pole with a staple gun, then keep wrapping it until you reach the top.After the platforms are attached to the posts, simply cover each one with carpet, wrapping the edges down underneath the platform and attaching with either wood screws or staples just as you did with the base.If you want, you can affix a kitty bed with sides on top of one of the shelves. Also, the picture shows shelves with sides on them: I'm including sides for the shelves in these instructions because they can be fairly difficult to make and your cat will like it just fine without them. You can choose round, square, or rectangular platforms. In the photograph, all of the shelves are round.Putting the bolts through the holes in the shelves first, then through the brackets, will leave the bigger, bulkier ends underneath the shelves and not visible. Do this by setting the platforms on top of their posts, marking where the holes need to be, then drilling holes for the bolts to go through. After the posts are wrapped, secure the platforms to the top of the posts with brackets.Secure at the top with a few more wood screws so it won't come undone. Wrap the rope around and around the post, covering up the end and then working your way all the way to the top. Don't worry about having it at the exact bottom: You can overlap the rope over it (thereby covering the end and making the rope more secure). Attach the end of the rope near the bottom of a post using a wood screw.After the carpet is secured to the base, set each post in its spot and attach to the brackets using the 1" wood screws.If your wood screws aren't short enough, you will need to use a staple gun instead. When you drill them in, make sure they don't come out the top of the board. Attach the edges of the carpet under the base using the short wood screws.This will leave the brackets uncovered and the carpet in place. Push the carpet all the way down to where it will sit. Cut just an X where the post will go at first, then make sure the carpet is in the exact right place so that the brackets come through the hole. Set the carpet on top of the base, then mark where you will need to cut holes for the posts. Get a piece of carpet big enough to cover the entire top of the base with several inches left over on all sides. Now that all the brackets are in place, you will want to carpet the base.Test the post to make sure it fits and make adjustments if necessary. Do this for each of the bolts until all of the brackets are in place. Feed a bolt up from the bottom of the base, through the hole in the bracket, and then put a nut on it.You may want to countersink the area around each hole on the bottom of the base to prevent the bolts from coming in contact with the floor and scratching it up. Do this for each of the four L-brackets that are going around each post. Move the bracket out of the way and drill holes for the bolts all the way through the base. Arrange one of the L-brackets along one side of each post's outline and mark where you need to drill the holes.(Tip: Make sure you use one of the posts as a stencil, since 4" x 4"s are not always exactly 4" x 4"). Mark the outlines of the 4" x 4"s on the base, so you have three 4" x 4" squares outlined on the base. Try to get them fairly close to center so the structure will be steady. On the base, mark out where you want the posts.Don't forget to check the cut bin at the store: Sometimes you'll find some great usable pieces there. You may want to alter the post length a little so that one 8' 4" x 4" post will be enough for your entire project. Often your neighborhood home improvement store can do this for you for little or no cost. First, cut the wood to the desired sizes.This article has been viewed 800,148 times. This article has 37 testimonials from our readers, earning it our reader-approved status. WikiHow marks an article as reader-approved once it receives enough positive feedback. She also teaches at the Boca Raton Museum Art School - formerly at SVA in Manhattan. Renée has even painted a portrait of celebrity, Vanilla Ice. She has garnered numerous awards including “Artist of the Year” from The Bloomfield Art League and First Prize from the Boca Raton Museum Artist’s Guild. Renée is featured in over 68 shows and galleries including a one-woman museum show at the Paterson Museum. She has studied under internationally renowned portrait artists John Howard Sanden, David Leffel, Robert Beverly Hale, Clyde Smith, and Leonid Gervits. With over 50 years of experience, Renée specializes in painting realistically in oil and capturing the soul of the person. Renée Plevy is an Internationally Acclaimed Portrait Artist from New York/Palm Beach who has painted The Grand Dames of Palm Beach and various celebrities and community leaders. This article was co-authored by Renée Plevy.
0 Comments
Read More
Leave a Reply. |